![]() |
Need advice on reinstallation of abutment washer |
Post Reply ![]() |
Page <1234> |
Author | |
Airitis ![]() Red Ryder Member ![]() ![]() Joined: October-06-2016 Location: PA Points: 1198 |
![]() ![]() ![]() ![]() ![]() |
Glad to hear that the tabs were still there even if not at 3 and 9. Good work and keep us posted on the forensics!
Russ. |
|
Air-It-Is
|
|
![]() |
|
Bryno ![]() Red Ryder Member ![]() ![]() Joined: April-17-2023 Location: Mesa Az Points: 108 |
![]() ![]() ![]() ![]() ![]() |
![]() |
|
![]() |
|
Bryno ![]() Red Ryder Member ![]() ![]() Joined: April-17-2023 Location: Mesa Az Points: 108 |
![]() ![]() ![]() ![]() ![]() |
![]() |
|
![]() |
|
Bryno ![]() Red Ryder Member ![]() ![]() Joined: April-17-2023 Location: Mesa Az Points: 108 |
![]() ![]() ![]() ![]() ![]() |
![]() |
|
![]() |
|
Bryno ![]() Red Ryder Member ![]() ![]() Joined: April-17-2023 Location: Mesa Az Points: 108 |
![]() ![]() ![]() ![]() ![]() |
Still trying to figure out this picture thing but I wanted to finish up this post. Again the point was to show that some of the daisy guns like the one in question appear to have been mismanufactured. Causing the staking tabs for the abutment washer to never be folded over subsequently allowing the equipment washer to fall out during seal replacement. You can see that the tabs are definitely not at 3:00 and 9:00 and the plunger head shows signs of having been rubbing on one tab for the duration of his life.
|
|
![]() |
|
Bryno ![]() Red Ryder Member ![]() ![]() Joined: April-17-2023 Location: Mesa Az Points: 108 |
![]() ![]() ![]() ![]() ![]() |
![]() |
|
![]() |
|
Airitis ![]() Red Ryder Member ![]() ![]() Joined: October-06-2016 Location: PA Points: 1198 |
![]() ![]() ![]() ![]() ![]() |
Nice detective work there, B. On to another project?
Russ. |
|
Air-It-Is
|
|
![]() |
|
Bryno ![]() Red Ryder Member ![]() ![]() Joined: April-17-2023 Location: Mesa Az Points: 108 |
![]() ![]() ![]() ![]() ![]() |
Well thanks Russ. And of course there's a few in the pipe. Meanwhile this one isn't actually done. I have a daisy dollar token that I just polished up and I intend to inlay it in the stock and then laser engrave around it. When I get done I will post a photo. I hope.
|
|
![]() |
|
cobalt327 ![]() Red Ryder Member ![]() ![]() Joined: November-15-2013 Points: 3046 |
![]() ![]() ![]() ![]() ![]() |
Bryan, good job on the photos- were you able to use the share link at imgur?
|
|
![]() |
|
Bryno ![]() Red Ryder Member ![]() ![]() Joined: April-17-2023 Location: Mesa Az Points: 108 |
![]() ![]() ![]() ![]() ![]() |
Yes sir. Thanks Mark. I sent you an email I'm sure you'll see it with the details. It's a little different using your cell phone it's kind of an app if anybody else gets stuck let me know.....the IT guys will clearly trying to justify their position when they built this stuff.
|
|
![]() |
Post Reply ![]() |
Page <1234> |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |